Auto Intensity Control of Street Lights

Street lights are controlled manually in olden days. These days automation of street lights has emerged. But one can observe that there is no need of high intensity in peak hours i.e. when there is no traffic and even in early mornings. By reducing the intensity in these times, energy can be saved to some extent.

There are many methods to save the power like Switching the street light on detecting vehicle , Street light controlling using LDR and relays etc. The proposed circuits controls street light intensity by calculating the peak hours.Two circuits are shown in this article,one explaining the street light control using ATmega8 and second explains street light controlling using PIC microcontroller. Most commonly found street lights are HID or High Intensity Discharge lamps, which consume a lot of power. In order to save energy, the circuits are designed with high intensity LEDs in place of HID lamps.

Auto Intensity Control of Street Lights using ATmega8

Circuit Principle

The main principle of this project is to Control the intensity of street lights using PWM.Peak hours of a particular area are calculated and accordingly PWM signal is adjusted by microcontroller to increase or decrease the intensity of street lights.

These peak hours can be calculated by considering parameters like traffic density,time, light intensity of the environment.

Auto Intensity Control of Street Lights Circuit Diagram

Read More

Car Parking Guard Circuit Using Infrared Sensor

Introduction: While parking the car the driver should be more careful because he cannot see the back of the car while parking or taking reverse, if there is any obstacle and ran over it might be  get damage to the car. Our project will help the person in the driving seat and give alarm if there is any obstacle or a wall while parking or while driving in reverse.

Block Diagram of Car Parking Guard:

The IR sensor will detect the obstacle with in 100cm, if there is any obstacle it will sense and give information to the tone detector which will enable the LM555 timer to generate a PWM for the buzzer. The LM555 will generate the pulse which helps to buzz the buzzer so driver can understand that there is an obstacle.

Main Component Explanation:

LM567: is a tone detector which can interpret the frequency generated by the other component and give the output according to the application designed by the engineer. For example if a component is attached to the input of LM567 which can generate a 40 kHz signal , but we to function the following circuit when the component has reached to the 40KHz. At this decision making we will use tone detector. The tone detector is mainly used in touch tone decoders, ultrasonic controls, frequency monitoring and control etc.

LM555: is a timer which can generate a PWM signals in various width and duty cycles. The 555 timer is mainly used to control the other peripherals like motors, detectors, regulators etc.

IR Sensor: the main function of the IR sensor is to produce a beam for certain distance (the distance of the beam is always depends on the IR sensor, different IR sensor have different range of beam distance) if the there is any obstacle in the beam it will conduct and give signal.

Photo Darlington Transistor: the photo darlington transistor will act as a photo detectors. They will conduct to the light or electro magnetic signals. The main function of this transistor is to amplify the input signal of the transistor. But it will work slowly when compared to the other transistors. It is having a maximum frequency of 20 KHz.

Circuit Diagram of Car Parking Guard:

Read More

Water Level Controller using 8051 Microcontroller

Water Level Controller using 8051 Microcontroller project will help in automatically controlling the water motor by sensing the water level in a tank. This article explains you how to detect and control the water level in an overhead tank or any other container. This system monitors the water level of the tank and automatically switches ON the motor whenever tank is empty.

The motor is switched OFF when the overhead tank or container is FULL. Here, the water level of the tank is indicated on LCD (Liquid crystal Display). Using this system, we can avoid the overflow of the water.

We have already seen How water level indicator circuit works using AVR Microcontroller in the earlier post. But, here we are designing the circuit which is used to detect and control the water level automatically in overhead tank using 8051 microcontroller.

In this system, water sensing can be done by using a set of 4 wires, which are placed at different levels in tank. DC supply probe is placed at the base of the tank. 

Water Level Controller using 8051 Circuit Principle

This system mainly works on a principle that “water conducts electricity”. The four wires which are dipped into the tank will indicate the different water levels. Based on the outputs of these wires, microcontroller displays water level on LCD as well as controls the motor.

Initially when the tank is empty, LCD will display the message LOW and motor runs automatically. When water level reaches to half level, now LCD displays HALF and still motor runs.

When the tank is full, LCD displays FULL and motor automatically stops. Again, the motor runs when water level in the tank becomes LOW.

Water Level Controller using 8051 Microcontroller Circuit Diagram

Read More

Obstacle Avoiding Robot using Arduino

Robotics is an interesting and fast growing field. Being a branch of engineering, the applications of robotics are increasing with the advancement of technology.

The concept of Mobile Robot is fast evolving and the number of mobile robots and their complexities are increasing with different applications.

There are many types of mobile robot navigation techniques like path planning, self – localization and map interpreting. An Obstacle Avoiding Robot is a type of autonomous mobile robot that avoids collision with unexpected obstacles.

In this project, an Obstacle Avoiding Robot is designed. It is an Arduino based robot that uses Ultrasonic range finder sensors to avoid collisions.

Circuit Diagram

Read More

Arduino Alarm Clock

In this project, we designed an Arduino based Real Time Clock with alarm. A Real Time Clock or RTC is a battery powered clock that measures time even when there is no external power or the microcontroller is reprogrammed.

An RTC displays clock and calendar with all timekeeping functions. The battery, which is connected to the RTC is a separate one and is not related or connected to the main power supply.

Read More

Portable Ultrasonic Range Meter

Sound is a phenomena that is a result of vibration of materials. Sound is characterized as a mechanical wave that carries mechanical energy.

For the transmission of this energy between transmitter and receiver, presence of a medium is necessary. The medium can be solids, liquids or gases.

Read More

Arduino LED Matrix

An LED matrix is a two dimensional array of LEDs that can be used to display symbols, characters or even images. Based on the orientation of the LEDs in the matrix, there can be two types of LED matrices.They are Common Row Anode and Common Row Cathode.
LED matrix modules are one of the commonly used display devices and are used in major applications like electronic display panels and notification systems.

In this project, an Arduino Uno board is integrated with an 8 X 8 LED matrix to display information (even scrolling information and images can be displayed).

Circuit Diagram

Read More

Rotary Encoder With Arduino

A Rotary Encoder is an electromechanical device that converts angular movement of the shaft to analog or digital code.

Rotary Encoders can be found in radio equipment like amateur radio or hand held, where non-stop or continuous 3600 rotation is required for tuning to right frequency.

In this project, the working of Rotary Encoder is explained with the help of Arduino. The following sections are dived into introduction to rotary encoders, circuit and working.

Circuit Diagram

Read More

Frequency Counter Using Arduino

Frequency Counter, as the name indicates, is an electronic device or component, which is used to measure the frequency of a signal. In case of a repetitive electronic signal, a frequency counter measures the number of pulses in that signal.

We generally use an oscilloscope to depict the signal, calculate the time period of the signal and finally convert it to calculate the frequency of the signal. But, oscilloscopes are very expensive and everyone cannot afford it.

Hence, a simple Digital Frequency Counter can be built which might come in handy to measure the frequency of a clock signal, for example.

In this project, an Arduino based Digital Frequency Counter is designed to measure the frequency of an incoming signal.

Circuit Diagram

Read More

8051 Microcontroller Memory Organization

In the previous tutorial on 8051 Microcontroller, we have seen the 8051 Microcontroller Introduction and Basics, Pin Diagram, Pin Description and the Architecture overview. In this tutorial, we will continue exploring 8051 Microcontroller by understanding the 8051 Microcontroller Memory Organization.

When the differences between microprocessor and microcontroller are mentioned in the previous tutorial, the main difference can be stated as on-chip memory i.e. a Microcontroller has both Program Memory (ROM) and Data Memory (RAM) on the same chip (IC) whereas a Microprocessor has to be externally interface with the memory modules.

Hence, it is clear that the memory is an important part of the 8051 Microcontroller Architecture (for that matter, any Microcontroller). So, it is important for us to understand the 8051 Microcontroller Memory Organization i.e. how memory is organized, how the processor accesses each memory and how to interface external memory with 8051 Microcontroller.

Before going in to the details of the 8051 Microcontroller Memory Organization, we will first see a little bit about the Computer Architecture and then proceed with memory organization. 

Types of Computer Architecture

Basically, Microprocessors or Microcontrollers are classified based on the two types of Computer Architecture: Von Neumann Architecture and Harvard Architecture.

Von Neumann Architecture

Von Neumann Architecture or Princeton Architecture is a Computer Architecture, where the Program i.e. the Instructions and the Data are stored in a single memory.

Since the Instruction Memory and the Data Memory are the same, the Processor or CPU cannot access both Instructions and Data at the same time as they use a single bus.

This type of architecture has severe limitations to the performance of the system as it creates a bottleneck while accessing the memory.

Read More

Arduino Traffic Light Controller

The use of personal vehicles is very common now a days and a result, the number of vehicles on the roads are exponentially increasing. Roads without any supervision or guidance can lead in to traffic congestions and accidents.

Traffic Lights or Traffic Signals are signalling devices that are used to control the flow of traffic. Generally, they are positioned at junctions, intersections, ‘X’ roads, pedestrian crossings etc. and alternate the priority of who has to wait and who has to go.

The traffic lights will provide instructions to the users (drivers and pedestrians) by displaying lights of standard color. The three colors used in traffic lights are Red, Yellow and Green.

The system must be used to control the traffic lights for smooth and safe movement of traffic. These control systems consists of electro mechanical controllers with clockwork mechanisms or modern solid state computerised systems with easy setup and maintenance.

In this project, an Arduino based Traffic Light Controller system is designed. It is a simple implementation of traffic lights system but can be extended to a real time system with programmable timings, pedestrian lighting etc.

Circuit Diagram

Read More

Build a Simple Arduino Calculator

A Calculator is a device that is used to perform simple arithmetic operations to complex mathematical calculations. The rise of calculators can be seen from devices like Abacus to credit card sized complex electronic solid state devices in the modern day usage.

Apart from small calculators, which can be used to perform simple arithmetic calculations, calculators also come in complex scientific outlook that can perform various mathematical and statistical operations like trigonometry, algebra, calculus, etc. But such complex scientific calculators can be very costly.

In this project, we will design a simple arithmetic calculator using Arduino UNO, a 16 x 2 LCD display and 4 x 4 Matrix Keypad.

Circuit Diagram

Read More

Arduino Mail Notifier

Physical Mail or Post is a method of transporting documents, packages, cards, parcels and letters. This service is usually done by a postal service system. Mail is usually delivered by mail man post man to our homes. We get important documents like bills, invitations, bank statements etc. in mail.

If we don’t check our mail box regularly, we might miss the deadlines for payment of bills etc. It is a tedious job to regularly check for mail as mail boxes are often placed outside the house or in some cases, a common place at the end of the street.

Hence, in this project, a simple but efficient mail notifier system is designed using Arduino and few other components. This system notifies the user whenever there is a mail and hence avoiding the need to check for mail frequently.

The project is based on Arduino, RF Module (RF Transmitter and Receiver) and a light sensor (Photo resistor or LDR).

Circuit Diagram

Since the project is based on RF Modules, the circuit is divided in to transmitter and receiver.

The following image shows the circuit diagram of the Transmitter or Sender part of the project.

Read More

Arduino Home Automation Using RF

Home automation is one of in demand concepts in today’s world. Hobbyists do simple automation systems with the components readily available. If we are more concerned about the reliability and performance of the system, then we can go for the expensive Home Automation Consoles.

Home automation reduces the physical efforts and integrates the control for any number of appliances in to a single control unit. Hence, a simple home automation system is a remote control of different electrical appliances i.e. turning them on or off with the help of a remote.

There are many ways to implement this remote control system. With the extensive use of smart phones and tablets, Bluetooth may be the best option to implement the home automation. And one is implemented here in Bluetooth based Home Automation using Arduino.  The other methods of remote controlled home automation system are ZigBee, Wi-Fi, Radio Frequency (RF Module), GSM etc.

In this project, a simple but efficient home automation system using RF Module (Transmitter – Receiver pair) is designed. The system is designed with Arduino (ATmega 328) as the main processing unit.

Circuit Diagram

The circuit diagram is divided in to the transmitter section and receiver section for easy understanding. The transmitter section of the project is shown on the following image.

Read More

Touch Dimmer Switch Circuit using Arduino

A Touch Dimmer Switch Circuit is a simple project, where the dimmer action is achieved with the help of a Touch Sensor. While a regular switch is used to simply turn ON or OFF a light, a Dimmer (or Dimmer Switch) will allow us to control the brightness of the light. Without a Dimmer Switch, the light bulbs tend to glow at full brightness consuming maximum power. If full brightness is not required, then Dimmer Switches can be used and save some energy. With the help of a Dimmer Switch, we can vary the brightness from fully off to fully on.

Different light bulbs need different dimmer switches and there are different types of Dimmer Switches available in the market. Some of the commonly found Dimmer Switches are Slider type and rotary type.

In this project, we have designed a Touch Dimmer Switch using Arduino. The Touch Dimmer Switch Circuit is implemented using a Touch Sensor. The circuit design, components and working of the project is explained in the following sections.

Read More

Arduino Based Color Detector

A Color Sensor, as the name suggests, is a device that senses or detects colors. A color sensor will use an external means of emitting light (like an array of white LEDs) and then analyse the reflected light from the object in order to determine its color.

Color sensors will give an accurate color of the object. There are a wide range of applications of color sensors like sorting objects by color, quality control systems, printer color enhancement etc.

In this project, we have designed a simple Arduino Color Sensor application, which has an ability to detect different colors. We have used TCS3200 color sensors for this purpose. Introduction to color sensor, circuit diagram and working of the Arduino Color Sensor project are explained below.

Circuit Diagram

Read More

Use 5v Relay Arduino

Arduino is a microcontroller based prototyping board that runs on small DC power. A Relay is a device that helps microcontrollers (or microcontroller based boards) like Arduino to switch on or off different household appliances like motors, lights, water heaters, television and fans etc.

Today, Arduino is being used for a wide range of applications like controlling LEDs, monitoring temperature, logging data and turning on motors etc. Another important task that can be accomplished by the Arduino is controlling a 5V Relay to operate high voltage AC appliances and devices.

Arduino family of microcontrollers, like UNO, Nano and Mega etc. can be programmed to control a simple 5V relay i.e. switch it on or off on the event of pushing a button, reading the value of temperature from a thermistor or just by setting up a predefined timer.

Read More

Arduino based Wireless Doorbell

Traditional Doorbells are wired devices and are usually fixed at one place. They are becoming obsolete because of these reasons and are gradually being replace by advanced Wireless Doorbell Devices. With a wireless doorbell, the position of the switch and the bell is not fixed.

We can place it anywhere we want and also the installation is pretty simple. The setup of wireless doorbell doesn’t require any internal wiring. Also, if the wired doorbell is not fixed while construction, we need to make holes for wiring and installation.

In this project, we have designed an Arduino based Wireless Doorbell using simple hardware. The project is implemented using RF Module for wireless communication and also an Arduino UNO board to analyze the data.

Read More